ONT LEOX-GPON-LXT-010H-D

http://xbest.pl/index.php?p5117,ont-gpon-lxt-010h-d-leox-1x2-5ge-1xgpon-sc-apc
https://lafibre.info/remplacer-livebox/mise-en-route-leox-lxt-010h-d/252/
https://lafibre.info/remplacer-livebox/trouver-la-valeur-hw_hwver-pour-leox-lxt-01g-d-lxt-010h-d/
https://wiki-archive.opencord.org/attachments/1966449/2557137.pdf

Manufacturer : marcinkuczera https://lafibre.info/profile/marcinkuczera/ https://lafibre.info/pm/?sa=send;u=41150

IP: 192.168.100.1
login/passwd: leox / leolabs_7
telnet and HTTP web interface

Note : Some OLT (Huawei) seems to be very restrictives.
Firstly, try to skip some optional settings (HW_HWVER, OMCC, HW_CWMP)

Secondly, get all default values
It is a best practice to read default values before modify them...

flash all
flash all | grep GPON_SN
flash all | grep PON_VENDOR
Copy

1. set the mandatory params
   You have to set GPON serial and vendor ID

# ONT LEOX-GPON-LXT-010H-D
GPON_SN=HWTCxxxxxxxx
# flash set PON_VENDOR_ID HWTC
PON_VENDOR_ID=HWTC
Copy

Then, on the WEB interface, you can check the PON Status :

Vendor Name     LeoLabs
Part Number     LXT-010H-D
Temperature     75.074219 C
Voltage 3.401500 V
Tx Power        1.076726 dBm
Rx Power        -17.077437 dBm
Bias Current    0.000000 mA
GPON Status
ONU State       O5
ONU ID  2143923176
LOID Status     Initial Status
Copy

If you do NOT have O5 for the ONU State, try the following commands and check again the web page...
Some Huawei OLT (ISP side) are very restrictive, that's why the following params could be required.

2. set hardware version (should not be required)
   It is better to SKIP this to avoid unexpected reboot (by Orange).

# flash set HW_HWVER HWTCA240FA
HW_HWVER=HWTCA240FA
Copy

Here are some correct ONT hardware versions :

Note: If you encounter some DHCP issues and everything seems right, try to change the HWVER without modifying SERIAL number. For example, Huawei ONT serial number with a Livebox6 HWVER.

3. OMCC compliance
   This param seems to be important on some OLT. Try to skip this, but use if you encounter issues...
   See https://wiki-archive.opencord.org/attachments/1966449/2557137.pdf (cf. ONU-G ME #256, ONU2-G ME #257, Software Image ME #7)
   80 : (default) do not work well
   B0 : (HG8010H) do not work well too
   A0 : everything is OK
   ONU-G / ME #256
   ONU2-G / ME #257
   Software image / ME #7

Note : 160d == AOh

# flash set OMCC_VER 160
OMCC_VER=160
# flash set OMCI_SW_VER1 HWTCA31610115
OMCI_SW_VER1=HWTCA31610115
# flash set OMCI_SW_VER2 HWTCA31610115
OMCI_SW_VER2=HWTCA31610115
Copy

4. Manufacturer

# flash set HW_CWMP_MANUFACTURER HUAWEI
HW_CWMP_MANUFACTURER=HUAWEI
# flash set HW_CWMP_PRODUCTCLASS HG8010H
HW_CWMP_PRODUCTCLASS=HG8010H
Copy

5. OLT compat (customized, will also unlock advanced params on web interface)

# flash set OMCI_OLT_MODE 3
OMCI_OLT_MODE=3
Copy

Possible values are :

<option value="0">Default Mode</option>
<option value="1">Huawei OLT Mode</option>
<option value="2">ZTE OLT Mode</option>
<option value="3" selected="">Customized Mode</option>
Copy

omcicli mib get all
flash all
flash all | grep xxx
Copy

Before upgrade, make a backup of files rtl8290b.data and europa.data from /var/config folder. These files include optical calibration of your ONT’s laser, if you accidentally delete or ruin them, your ONT will be unusable.

You must also rollback the HW_HWVER to 'LXT-010H-D'.

flash set HW_HWVER LXT-010H-D
Copy

• Versions :
  Original version is V3.3.2L6
  Last known version (01/2023) is V3.3.2L7

• On the router / server :

netcat -l  -p 10000  > europa.data
Copy

• On the LEOX :

busybox nc 192.168.x.y 10000 < /var/config/europa.data
Copy

• Do the same for /var/config/rtl8290b.data

Then, upgrade firmware via web interface...
Do not forget to re-apply the good value if it was previoulsy required (flash set HW_HWVER HWTCA240FA).